from wikiHow - The How to Manual That You Can Edit
Farm and heavy equipment uses a hydraulic pump, valve spools, and cylinders to perform their tasks. These components are interconnected with a series of steel tubes and steel reinforced rubber hoses, and the hydraulic oil may eventually begin to leak through these hoses, making it necessary to replace them. It can be a dirty job, but doing it yourself can save considerable expense and time.
Steps
- 1Locate the problem hose. This may be obvious if the hose has burst, since they typically handle oil at over 2000 PSI pressure, and one that bursts will discharge a large amount of oil in a short time. If the situation is a small leak, though, you will need to observe where the oil is dripping, and follow the wet trail it leaves to the source. Never use your hands or body parts to find the leak. Use cardboard, paper or hydraulic leak detection fluid so no oil injection is accured. A good hydraulic shop stocks leak detection additives that assist on location the leak safely.
Finding the leaking hose by looking for wet hoses and dripping oil.
- 2Assess how many components must be removed to facilitate replacing the damaged hose. Always label the component removed by number and letter so replacement of parts can be reinstalled with ease. This may include housings, guards, clamps, other hoses, hydraulic cylinders, and more. Follow the hose from one end to the other, noting the route you will use to uninstall and reinstall it. Putting a number and letter on the ports and hose ends.
To remove the correct hose, the other hoses must also be removed.
- 3Determine if the hydraulic component the hose serves, or any other hydraulic components which must be removed have a live load, or weight on them. If the oil in the system you are disconnecting is under pressure, it may blow out forcefully when the fittings which hold it are loosened, causing oil to be discharged under pressure. Relieve the pressure from these cylinders or components before proceeding.
Hoses that operate the backhoe boom.
- 4Make sure any attachments which are supported by the hydraulic cylinder the hose operates are lowered to the ground or blocked or chained up. The weight of an attachment can crush a mechanic if it suddenly falls when pressure is relieved in the cylinder that is supporting it.
Placing the backhoe boom on the ground to prevent it from falling.
- 5Get the tools you will need to perform the job of removing the hose. The fittings on the each end of the hose will be removed with a wrench, which may vary in size from 9/16 to over 1 1/2 inches. Many of these fittings are designed to swivel or turn as they operate, so two wrenches will be required to remove each of them. Hold the stationary side of the coupling with one wrench to prevent it from turning, and possibly damaging an O-ringwhile turning the other to seperate the coupling.
Tools for changing a hydraulic hose.
- 6Remove all clamps and attachments which will interfere with removing the hose. Often, the hydraulic cylinder itself will need to be removed or supported so that fittings can be accessed. Hydraulic cylinders are either bolted directly to the boss or fixture which it operates, or is anchored with a steel pin, such as the one in the illustration.
Supporting the unpinned hydraulic cylinder.
- 7Loosen the fitting that attaches the hydraulic hoseto the hydraulic system, either at a coupling, a cylinder, or the valve spool itself. Make sure the fitting turns at the threaded connection, and does not twist any other part. If needed, you may have to hold the fitting the hose is attached to with a separate wrench.
Loosening the fitting that connects the hose to the cylinder.
- 8Pull the hose off of the equipment when both ends are unfastened. Be aware that some hydraulic oil may leak from either or both connections, and the oil that is remaining in the hose will also dump out, so having a bucket handy to catch this spillage is a good idea.
- 9Plug the fittings that remain on the machine to keep debris from getting into the system during the interval the fitting is open. If you do not have oil dripping from the fitting, and do not have a plug with the correct threads on it, you may tie a clean rag around the fitting to protect it, but be careful if rain is in the forecast, since a rag won't protect the system from being contaminated with water.
- 10Wipe excess oil from the hose, and take it to an equipment supply store to have a new one ordered or made. Aftermarket manufacturers and OEM dealers supply replacement hoses and fittings which can be assembled while you wait, and are less expensive than ordering an original equipment manufacturer's product. Make sure the hyraulic shop that makes the hose will clean the hoses inside with a proper cleaning system not just shop air. A proper hydraulic hose shop like ASAP hydraulics will use a ultra clean system and install end caps to make sure no contaimnation will enter into the system. The end caps will keep the line clean until the line is routed through out the system and ready to install.
Clean the hose before taking it to a shop for replacement.
- 11Clean all the fittings on the equipment before reinstalling the hose. Make sure there is no dirt in the tubing or fitting which will end up in the hydraulic system when you are finished.
Clean the fittings where the new hose will attach.
- 12Plug the ends of your new hoses with a special cap or a clean rag before routing it through the equipment to where it goes. This will keep dirt and debris from being forced into the hose while installing it. Remove these temporary plugs immediately before installing the fittings where they mate up with their counterparts.
Ends of new hose closed off with rags to keep dirt out.
- 13Make sure the hose is in the correct location, and it has the proper amount of slack where needed when it is installed, then thread the fittings back on the cylinder or other component where they were removed. Tighten these connections snugly. You may have access to a specification book which recommends a torque to apply to each fitting, but failing this, tighten them as much as you can without risking damaging the seals or stripping the threads which hold them.
- 14Replace any clamps, guards, or other componentswhich were removed to accomplish the task. Align any cylinder pins which were removed, and reinstall them, and return any split or snap rings which hold them in place.
Clamps replaced that secure hoses, preventing damage when operating.
- 15Check the fluid level in the machine, crank it up, and check for leaks. If you have had a chance to clean all surfaces that were soiled by the initial leak, any leaks that occur now will be much easier to spot. Keep in mind some hydraulic circuits will require bleedingto remove air from the system prior to using the machine. This usually applied to steering and brake systems, but there are other situations where air can become trapped, such as a single action cylinder where the hydraulic supply is at a low point in the cylinder.
Tips
- Inspect any equipment before using. Standard industry inspections occur daily or at the beginning of each shift. Look for oil leaks, visible damage, or other indications of an unservicable condition.
- Replace hoses that have become cracked, scuff marked which the braided or wires are showing. Never put any body part against or near a hydraulic hose, fitting or tubing since any outside pressure may cause product failure and oil injection. Add this to your part of your regular maintenance, rather than waiting for a catastrophic failure, which may at least cause damage to other parts of the machine, and can even cause operator injury or death.
- Make sure you have all the tools you need before beginning.
- Be sure to locate the correct hose for the repair. Hoses are often routed very close together, making it difficult to identify the leaking hose.
- Mark any components which may be difficult to find the correct replacement location, especially if you are taking off a number of hoses, so these are not reinstalled in the wrong place.
- Keep bolts, pins, and lock rings in a container until you reinstall them.
- Clean all surfaces that will be accessed during the work if possible to make the job easier and cleaner.
- The safest method of checking for pin-hole leaks while the system is under pressure is simply using a sheet of paper held near the hoses. The location of the leak will be easily found.
- Things You'll Need
- Hydraulic oil under pressure can be injected directly into human tissue, causing serious tissue destruction. In particular, injuries to the hand can be deceptively benign appearing due to the small entry site, but all hand injuries require immediate and careful exploration by a hand surgeon due to the multiple tissue planes involved.[1]
- Hydraulic hoses have a steel wire(s) or spiral braiding reinforcing jacket underneath the outer cover, and when these become exposed and abraded, they can cause nasty cuts or abrasions.
- Hydraulic oils may be flammable, so leaks should be dealt with immediately upon discovery.
- Hydraulic components can weigh hundreds, or even thousands of pounds, so use care when working on them.
- Make sure hydraulic hose is replaced with an equal or better pressure rating. And if the fluid used is other then an SAE blend of 10 or 20 weight, as phosphate ester or synthetic blend. You must make sure the replacement hose meets your requirments via a pressure or suction line.
- Wrenches and tools for the removal and installation process
- New hoses
- Hydraulic oil to replace that which was lost through the leak
- A bucket to catch oil that leaks out when the hoses are disconnected
- Saftey gloves, glasses, mask, clean rags, oil dry, fire extinguisher, caps or plugs, tape and maker to label parts, shield to cover exhaust system to prevent fire is oil may spill on exhaust.